HOME

SHOP ORGONE CRYSTALS

528Hz

Vote For Warrior Matrix at Conspiracy Top Sites

daily quote warrior matrix

Follow Us On Facebook
List of materials for making orgonite
Goto page 1, 2  Next
 
Post new topicReply to topic
   Warrior Matrix Forum Index -> Questions and Answers
View previous topic :: View next topic  
Author Message
HaggisYann
Member


Joined: 22 Mar 2007
Posts: 1252
Location: Loch Ness

PostPosted: Sun Jan 25, 2015 3:24 pm    Post subject: List of materials for making orgonite Reply with quote

Basic list of orgonite making paraphernalia:

1. An organic vapour mask because resin fumes are very harmful.
2. Moulds (silicone cupcake to make some preliminary TBs and learn to use resin)
3. Metals (any will do, even kitchen foil put into a 'requisitioned' (lol) coffee grinder. (Never use for food/coffee again!)
4. Polyester resin (cheaper than epoxy for learning/ first pieces)
5. Clear quartz points.
6. Some protective gloves (surgical gloves, or the blue ones are better)
7. Hand cleansing cream used for removing resin. From a resin supplier.
8. Mixing pots. Either get ones from a supplier or use old ice-cream tubs, plastic cups or whatever you don't mind ruining.
9. Mixing sticks, lollipop sticks or 'proper' mixing sticks are nice.
10. Kitchen roll/ paper towel.
11. Graduated syringe for measuring catalyst if you are not going to 'wing it' instead of using measuring cups from a resin supplier.
12. Protective goggles has been recommended by some, as resin fumes can absorb through eyes.
13. A place which is not enclosed to pour in, as the fumes are dangerous and will linger.
14. A piece of board to lay on the ground or old trestle table to put everything on.
15 A storage tub or something to pop on top of the board when done so that rain or airborn stuff doesn'n mess up the piece. Birds etc lol. I place a heavy stone ontop of a storage tub because it's windy where I live.
16. A sledge hammer and cardboard box to smash up metal turnings inside (wear protective eye-gear)
17. Wooden kebab sticks are handy for poking things into place while pouring.

Please add anything else to this list
_________________
- Julian


Last edited by HaggisYann on Sun Jan 25, 2015 5:47 pm; edited 1 time in total
Back to top
View user's profile Send private message
028956blh
Member


Joined: 03 Mar 2014
Posts: 360
Location: United States

PostPosted: Sun Jan 25, 2015 3:57 pm    Post subject: Reply with quote

Outstanding post Julian! Regarding disposable gloves, I've tried nitrile, latex, and vinyl and prefer vinyl hands down. nitrile and latex fit too snuggly and i had an allergic reaction to the latex. Vinyl is just right!

Brett
Back to top
View user's profile Send private message
Lena
Moderator


Joined: 24 Jan 2005
Posts: 2821
Location: on the right after the big tree

PostPosted: Sun Jan 25, 2015 4:07 pm    Post subject: Reply with quote

That is a great list!

One other thing to keep in mind which you will not notice until you have actually poured it to make sure the work surface is level... which you will only notice once the pour has been done and the pieces look kinda lopsided...

I also like to keep a container of lacquer thinner close by in case there are any spills or drips... Rolling Eyes

If you have long hair you want to pull it back... cause once you have sticky gloves on it can be messy and the habit of just pulling your fingers through it can be almost automatic.

Lena
_________________
Change happens when we become aware of what we are already doing.

www.LenaRocks.com
Back to top
View user's profile Send private message Send e-mail
HaggisYann
Member


Joined: 22 Mar 2007
Posts: 1252
Location: Loch Ness

PostPosted: Sun Jan 25, 2015 4:39 pm    Post subject: Reply with quote

Thx Smile
_________________
- Julian
Back to top
View user's profile Send private message
Sensei
Site Admin


Joined: 24 Jan 2005
Posts: 6634
Location: Here Now. Somewhere Else Later

PostPosted: Sun Jan 25, 2015 6:32 pm    Post subject: Reply with quote

18. A positive, cheerful and balanced state of mind.

Julian that is great.

Thank you !

Sєηѕєι
_________________
Thank you for supporting WarriorMatrix at:
http://www.OrgoneCrystals.com
and
http://www.LemurianCrystal.com
Please, share...
http://www.OrgoniteInfo.com
Back to top
View user's profile Send private message Send e-mail Visit poster's website
028956blh
Member


Joined: 03 Mar 2014
Posts: 360
Location: United States

PostPosted: Sun Jan 25, 2015 7:41 pm    Post subject: Reply with quote

Lena,
Great comment about having a level work surface, particularly when using molds like martini glasses. When using Ateco pyramid molds, fill a cheap plastic container (from dollar store) with sand, set the mold in it, level it and u are good to go. And if you drip catalyzed resin in the sand, easy clean up. Simply remove hardened resin ball from sand.

Brett
Back to top
View user's profile Send private message
Lena
Moderator


Joined: 24 Jan 2005
Posts: 2821
Location: on the right after the big tree

PostPosted: Sun Jan 25, 2015 9:03 pm    Post subject: Reply with quote

The sand is a wonderful idea!!!

I have done something similar with using aluminum shavings rather than sand but like your idea better Smile

Lena
_________________
Change happens when we become aware of what we are already doing.

www.LenaRocks.com
Back to top
View user's profile Send private message Send e-mail
Kieron
Member


Joined: 28 Apr 2014
Posts: 581
Location: Nowhere Man

PostPosted: Sun Jan 25, 2015 10:15 pm    Post subject: Reply with quote

I would suggest finding a way tor raise your workbench or work surface somehow. Trust me, newbies won't think of this until they are in the middle of pouring. Rolling Eyes (yes, that's me!) I have used cinder blocks at each corner of the bench or work-table, for all kinds of things such as potting plants or repairing something. Nothing ruins my good mood or concentration quite like a sore neck or aching lower back from leaning over or bending too long.

Clean dirt or soil is also fine if you can't locate sand. Just make sure there are no large pebbles or stones in the bucket of dirt that could deform the mold or set the mold crooked.
Back to top
View user's profile Send private message
orgone-growth
Member


Joined: 02 Jan 2014
Posts: 284
Location: United States

PostPosted: Mon Jan 26, 2015 7:12 am    Post subject: Reply with quote

Great List!!

I have found that using a high powered MP3 player during and after the pour enables one to play wonderful meditative tunes or solfeggio harmonics for the pour. Believe me you will get a great buzz from a nice vibe. Now if you place the MP3 player on top of a piece of cardboard (which covers your pour area) you will feel the vibration of the sounds as you are pouring, and via the molds perhaps your new creation will benefit as well??? Furthermore you can write intentions on the cardboard for that (and subsequent) pouring session.
Back to top
View user's profile Send private message AIM Address Yahoo Messenger MSN Messenger
Recycler
Member


Joined: 31 Jan 2015
Posts: 2
Location: Zone 7, USA

PostPosted: Sun Feb 01, 2015 8:12 am    Post subject: Reply with quote

Hi, guys...I have been reading this site for weeks. I feel, like I know you guys alreagy. Took me, a while 2 get signed up...anyway. I go for accupunture 2x a week. During each session many, long, thin stainless steel needles are used. Nice relaxing background music, during each session. Shame, that the needles are chucked. Can these needles be used (as is) or do they need to be curved? In orgonite making?
Back to top
View user's profile Send private message
HaggisYann
Member


Joined: 22 Mar 2007
Posts: 1252
Location: Loch Ness

PostPosted: Sun Feb 01, 2015 11:27 am    Post subject: Reply with quote

If it was me, I wouldn't use them. I can't explain why but they just don't feel right to me for orgonite. Maybe if they could be cut up into small pieces, but that seems a bit dangerous and time consuming, and you would need a lot of them. A metal scrubbie would be a better idea imo, and leave the needles to a sharps container!
Imagining sharp bits of needle in skin and possibly flying into eyes (Murphey's Law).
_________________
- Julian
Back to top
View user's profile Send private message
HaggisYann
Member


Joined: 22 Mar 2007
Posts: 1252
Location: Loch Ness

PostPosted: Sun Feb 01, 2015 11:47 am    Post subject: Reply with quote

Adding to the list:

A pair of tweezers for removing small bits of sharp metal from fingers.

Some antiseptic.
_________________
- Julian
Back to top
View user's profile Send private message
Scot
Member


Joined: 06 Jan 2013
Posts: 520

PostPosted: Sun Feb 01, 2015 4:48 pm    Post subject: Reply with quote

Remember it is not very complicated at all.
Thanks HY for this.
It can look ominous and tough at the start, but after a time or two one sees that it really is quite easy.


S
Back to top
View user's profile Send private message
Ruth
Moderator


Joined: 29 Mar 2010
Posts: 3269
Location: Oregon

PostPosted: Sun Feb 01, 2015 7:25 pm    Post subject: Reply with quote

Recycler wrote:
Hi, guys...I have been reading this site for weeks. I feel, like I know you guys alreagy. Took me, a while 2 get signed up...anyway. I go for accupunture 2x a week. During each session many, long, thin stainless steel needles are used. Nice relaxing background music, during each session. Shame, that the needles are chucked. Can these needles be used (as is) or do they need to be curved? In orgonite making?


A member some time back made orgonite with the needles. Don't know if they had been used. The piece came out nicely, as I recall. Don't have time to search, but if you google "Warrior Matrix + needles" you can probably find the pictures.

Ruth
Back to top
View user's profile Send private message
Recycler
Member


Joined: 31 Jan 2015
Posts: 2
Location: Zone 7, USA

PostPosted: Wed Feb 04, 2015 3:21 am    Post subject: Acupuncture needles Reply with quote

Thanks, Ruth, I will try that search. Winter time I have extra time on my hands (no garden). Wondering, if I should grind the needles down, or see if I can (curl) the needle up?
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topicReply to topic
   Warrior Matrix Forum Index -> Questions and Answers All times are GMT
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum