Vote For Warrior Matrix at Conspiracy Top Sites

daily quote warrior matrix

Follow Us On Facebook

New NanoShield 7.83 Hz.and 528 Hz.
New NanoShield 7.83 Hz.and 528 Hz.
How to Make Earthpipes (EP's)

Post new topicReply to topic
   Warrior Matrix Forum Index -> Recommended Reading
View previous topic :: View next topic  
Author Message

PostPosted: Tue Apr 12, 2005 9:48 pm    Post subject: How to Make Earthpipes (EP's) Reply with quote

How To Make Earthpipes: by Don Croft, edited by boney

Note: A photo tutorial is on www.ethericwarriors.com/viewtopic.php?p=389#389

1. Cut a length of 1 1/2 inch copper or aluminum pipe into 13" lengths

2. Thoroughly tape one end of each pipe closed. If you're not thorough, resin will leak out the bottom.

3. Temporarily tape or wire seven of the pipes together so that the whole will stand up by itself with the taped ends at the bottom. [Optional]

4. The orgonite "plug" in the bottom of each EP needs to be at least five inches long, so drop 2 or 3 oz of mixed orgonite in each pipe.

5. Select a suitable xtal for each pipe. We use xtals that are at least an inch long and at least a quarter inch thick and have one distinct point.

6. Cut 13" of bare copper wire. We use 18 gauge wire but the point is to use wire that's thick enough to hold a shape and thin enough to work easily. Those coil forms that Christy in Ireland makes are wonderful for making suitable coils. They're available from www.quebecorgone.com.

7. After bending the wire to resemble the end of a big screw, just like was done for the HHG, only smaller, pinch the small end of the coil around the middle of the crystal. Remember that the whole thing will have to fit easily in the pipe. You may want to tape or glue the coil to the crystal so the unit doesn't fall apart when you drop it down into the pipe.

8. Here's the mind bending bit: as with the HHG, these are being made upside down. The xtal in the Earthpipe points down into the ground. The hollow end of the pipe is the bottom. The cone shape of the coil flares away from the pointed end of the crystal. When the pipe is in the ground, the xtal points down and the cone coil opens upward from the middle of the xtal, sort of like a dart in a blowgun Wink

9. I measured the amount of orgonite in an Earthpipe and it's five ounces, so after you drop the xtal in the pipe in the proper orientation, just spoon in the remaining orgonite. If you mix it loosely enough, the mass of orgonite will fill in around the coil and xtal, don't worry. [To give you a visual, the taped end of the pipe is standing on your pouring surface. Some metal shavings and resin go in the pipe. You place the coil-wrapped crystal in the pipe with the crystal pointing up, so the large end of the coil goes in first. Hence, it's very helpful to glue the crystal to the coil. It's no fun to fish the crystal out of the resin when it falls out of the coil. -boney]

10. When you get to the target area, just pound the whole thing down into sufficiently soft, stone-free ground. I hammer the pipe with a six pound sledge hammer. It damages the pipe a little but that?s okay. Remember that the orgonite plug is in the top of the device. This takes advantage of the resonant cavity principle. [The empty end of the EP gets pounded into the ground so that the crystal is pointing through the empty space toward the ground. It's not as complicated as it sounds...you'll understand once you make one. -boney]

11. You need a six pound sledge hammer or so to knock these into the ground. Just hammer the end of the pipe in that case. If you can find a stream, swamp or estuary you can probably just push it all the way into the ground.
Back to top

Joined: 24 Jan 2005
Posts: 424

PostPosted: Wed Apr 13, 2005 4:46 am    Post subject: Reply with quote

These are my variations to the construction process that made it easy for me:

  • Wrap the closed end with aluminum foil, then tape in place.
  • A milk crate has as a lot of slots to hold the pipe upright.
  • Pour a layer of shavings in the pipe and drop the coiled crystal in. I make the largest ring of the coil just wide to fit in the pipe so it will stand upright when dropped in.
  • Pour layers of shavings and resin until 5+oz has been filled.
Back to top
View user's profile Send private message Send e-mail

Joined: 05 Feb 2005
Posts: 355
Location: Aberdeen, WA

PostPosted: Sat May 07, 2005 1:15 am    Post subject: Reply with quote

Well, I've been told many times that the only dumb question is the one that doesn't get asked...so here goes:

The crystal point is oriented down, toward the earth, right? But which side has the expanding part of the coil?

My eyes have a long way to go in healing, and I couldn't be sure looking at McGinty's *excellent* tutorial.

Back to top
View user's profile Send private message Send e-mail Visit poster's website

Joined: 13 Mar 2005
Posts: 119
Location: SW Herefordshire, UK

PostPosted: Sat May 07, 2005 10:59 pm    Post subject: Reply with quote


It is like a dart in a blow pipe, the coil is like the feather behind the dart (crystal), pointing towards the ground

Back to top
View user's profile Send private message Send e-mail Visit poster's website
Display posts from previous:   
Post new topicReply to topic
   Warrior Matrix Forum Index -> Recommended Reading All times are GMT
Page 1 of 1

Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum